PPPOE, access point - Revision history

Jimbo at 11:55, 3 January 2009

2009-01-03T11:55:19Z

2009-01-03T11:54:53Z

2008-06-04T22:08:04Z

Nat

2008-06-04T22:05:58Z

Nat

2008-06-04T22:05:40Z

Nat

2008-06-04T21:56:59Z

Nat

2008-06-04T21:56:23Z

Nat

2008-06-04T21:55:39Z

Nat

2008-06-04T21:52:36Z

PPPOE

2008-06-04T21:48:05Z

PPPOE

← Older revision		Revision as of 22:08, 4 June 2008
Line 139:		Line 139:

	then try to ping the internet...		then try to ping the internet...
		+
		+	then you shurely want to enable ppoe at boot so add the following in your /etc/rc.conf:
		+	ipv6_enable="NO"
		+	ppp_enable="YES"
		+	ppp_mode="ddial"
		+	ppp_profile="alice"
		+	ppp_nat="YES"
		+
		+
		+	===Dnsmasq===

← Older revision		Revision as of 22:05, 4 June 2008
Line 118:		Line 118:
	on the server do:		on the server do:
	ping 192.168.1.2		ping 192.168.1.2
		+
		+	if you can ping each other add the route in the client:
		+	on FreeBSD client or GNU/Linux client do the following:
		+	route add default gw 192.168.1.1
		+	then try to ping FreeBSD's website's ip:
		+	ping 69.147.83.33
		+
		+	if it works then add your dns to /etc/resolve.conf
		+	on the server do:
		+	cat /etc/resolv.conf
		+	then write down the 2 ips,then on the client edit /etc/resolv.conf and recreate the same resolv.conf as the server
		+
		+	alternatively you can copy the following in your resolv.conf...theses are the ip of opendns...as a temporary solution because:
		+	*opendns could be far from your location
		+	*opendns remplace the google querries from firefox's addressbar by his own version of google
		+	*see [http://en.wikipedia.org/wiki/Opendns wikipedia's entry on opendns] for more details
		+	here's the file:
		+	nameserver 208.67.222.222
		+	nameserver 208.67.222.220

@@ Line 107: / Line 107: @@
 on FreeBSD client do:
   ifconfig rl0 up
-  dhclient rl0
+  ifconfig rl0 inet 192.168.1.2 netmask 255.255.255.0
 or on GNU/Linux client do:
   ifconfig eth0 up
-  dhclient eth0
+  ifconfig eth0 inet 192.168.1.2 netmask 255.255.255.0

← Older revision		Revision as of 21:55, 4 June 2008
Line 100:		Line 100:
	we need to bring up the other wired network interface or the wifi(not the one that you used for connecting to the pppoe modem) card and assign an ip to it,but we will use the wired card for simplicity<br>		we need to bring up the other wired network interface or the wifi(not the one that you used for connecting to the pppoe modem) card and assign an ip to it,but we will use the wired card for simplicity<br>
	<i>note that you need an [http://en.wikipedia.org/wiki/Ethernet_crossover_cable Ethernet crossover cable] if you connect directly to the FreeBSD machine</i>		<i>note that you need an [http://en.wikipedia.org/wiki/Ethernet_crossover_cable Ethernet crossover cable] if you connect directly to the FreeBSD machine</i>
		+
		+	on the FreeBSD AccessPoint assign an ip to the interface:
		+	ifconfig rl0 up
		+	ifconfig rl0 inet 192.168.1.1 netmask 255.255.255.0
		+
		+	on FreeBSD client do:
		+	ifconfig rl0 up
		+	dhclient rl0
		+
		+	or on GNU/Linux client do:
		+	ifconfig eth0 up
		+	dhclient eth0

← Older revision		Revision as of 21:52, 4 June 2008
Line 95:		Line 95:
	ifconfig tun0 destroy		ifconfig tun0 destroy

−	~~then~~ if you stoped your connection restart it,we need it in order to test the nat(that means network address translation...we need this in order to share our connection,see [http://en.wikipedia.org/wiki/Network_address_translation the wikipedia article] if you are interrested)	+	====Nat====
		+	Then if you stoped your connection restart it,we need it in order to test the nat(that means network address translation...we need this in order to share our connection,see [http://en.wikipedia.org/wiki/Network_address_translation the wikipedia article] if you are interrested)
		+
		+	we need to bring up the other wired network interface or the wifi(not the one that you used for connecting to the pppoe modem) card and assign an ip to it,but we will use the wired card for simplicity<br>
		+	<i>note that you need an [http://en.wikipedia.org/wiki/Ethernet_crossover_cable Ethernet crossover cable] if you connect directly to the FreeBSD machine</i>

← Older revision		Revision as of 21:48, 4 June 2008
Line 95:		Line 95:
	ifconfig tun0 destroy		ifconfig tun0 destroy

−	then if you stoped your connection restart it,we need it in order to test the nat(that means network address translation...we need this in order to share our connection,see [http://en.wikipedia.org/wiki/Network_address_translation the wikipedia article if you are interrested)	+	then if you stoped your connection restart it,we need it in order to test the nat(that means network address translation...we need this in order to share our connection,see [http://en.wikipedia.org/wiki/Network_address_translation the wikipedia article] if you are interrested)